Light weight RLSAs with a honeycomb-type parallel plate are promising candidates for satellite antennas. However, the design of slot lengths and positions in honeycomb RLSAs consisting of a core, skin and adhesive layers involves time-consuming EM analysis. In this paper, an equivalent double layer model is devised for fast slot coupling analysis by the Method of moments (MoM) together with a simplified array design procedure. A fabricated antenna with a diameter of 900mm demonstrates the high directivity of 48.3dBi and a gain of 44.6dBi at 32GHz, with the reflection below -15dB. This antenna weighs only 1.16kg.

A transducer with a wide step from a post-wall waveguide to a hollow waveguide width is proposed which is tolerant against the aperture offset. The modes in the step width of about 1.50 wavelengths are stable for the aperture offset and the fields are not so perturbed while in the conventional stepped structure with step width of about 1.00 wavelength, the higher evanescent mode of TE30 is excessively enhanced by the aperture offset. The operation of the transducer with the wider step is robust for the fabrication errors in the millimeter wave band. It is also suggested that the anti-symmetrical TE20 mode which is excited only by non-zero offset or the misalignment of the aperture exists in both structures and can not be the dominant factor for the improvement. The transducers are designed and fabricated at 61.25 GHz using PTFE substrate with glass fiber of εr=2.17. The bandwidth for the reflection lower than -15 dB is almost unchanged (6.30-6.60 GHz) for the offset from -0.2 mm to 0.2 mm, while it is degraded in the conventional stepped structure, from 7.65 GHz for no offset to 3.30-5.70 GHz for the same range of the offset.

A post-wall waveguide-fed parallel plate slotted array is an attractive candidate for high efficiency and mass producible planar array antennas for millimeter wave applications. For the slot design of this large sized array, a periodic boundary wall model based on the assumption of infinite array size and a parallel waveguide is used. In fact, the aperture is large but still finite (10-40 wavelength) and the TEM-like wave is perturbed due to the narrow walls at the periphery of the aperture as well as the slot coupling; antenna efficiency is affected by the size and the aspect ratio of the aperture. All these observations imply the unique defects of oversized waveguide arrays. In this paper, the aperture efficiency of post-wall waveguide arrays is assessed as a function of size and aspect ratio of the aperture for the first time, both in theory and measurement. An effective field analysis for an electrically large oversized waveguide array, developed by the author, is utilized for determining the slot excitation coefficients and aperture illumination. It is predicted that the oversized waveguide array has a potential efficiency of 80-90% if the aperture is larger than 18 wavelength on a side and the gain is more than 30 dBi. A transversely wide aperture generally provides higher efficiency than a longitudinally long aperture, provided a perfectly uniform TEM wave would be launched from the feed waveguide.

A post-wall center-feed waveguide consisting of T-junctions is proposed for reducing the slot-free area of a parallel plate slot array antenna. The width of the slot-free area is reduced from 2.6 λ0 to 2.1 λ0. A sidelobe level in the E-plane is expected to be suppressed lower than that of the conventional center-feed antenna using cross-junctions. The method of moments with solid-wall replacement designs initially the T-junctions and HFSS including the post surfaces modifies only the reflection cancelling post. We have designed and fabricated a 61.25 GHz model antenna with uniform aperture illumination. The sidelobe level in the E-plane is suppressed to -9.5 dB while that of a conventional cross-junction type is -7.8 dB. Also, we suppress it to -13.8 dB by introducing a -8.3 dB amplitude tapered distribution in the array of the radiation slot pairs.

In this paper, we present the transmission characteristics control of a 125 GHz-band split-ring resonator (SRR) bandstop filter by coupling an alignment-free lattice pattern. We demonstrate that the transmission characteristics of the SRR filter can be controlled by coupling the lattice pattern; however, the required accuracy of alignment between the SRR filter and lattice pattern was below 200 µm. Therefore, we designed an alignment-free lattice pattern whose unit cell size is different from that of the SRR unit cell. S21 of the SRR bandstop filter changes from -38.7 to -4.0 dB at 125 GHz by arranging the alignment-free lattice pattern in close proximity to the SRR stopband filter without alignment. A 10 Gbit/s data transmission can be achieved over a 125 GHz-band wireless link by setting the alignment-free lattice pattern substrate just above the SRR bandstop filter.

Lightweight single-layer slotted waveguide array antennas are fabricated using plastic materials with metal-plating. A plastic material that has good heat-radiation properties is investigated. Three types of antennas are fabricated by milling, using ABS resin, heat-radiating plastic, and aluminum alloy. In measurements, all three types of antennas are confirmed to have almost the same VSWR and gain in the 25 GHz frequency band.

A novel analysis model for post-wall waveguide T-junctions is proposed. Equivalent solid-walls for the post-walls to have equal guided wavelength are corrected in the analysis model so that the wall thickness for the coupling windows is set to the difference in the width between the post-wall and the solid-wall waveguides. The accuracy of the proposed model is confirmed by comparing it to an HFSS analysis for the real structure of the post-wall waveguide T-junction including the post surfaces. 61.25 GHz model antennas are fabricated for experimental verification. The reflection of the antenna designed by the modified analysis model is suppressed to below -15 dB over a 5.6 GHz bandwidth, while that in the antenna designed by the conventional model is larger than -15 dB around the design frequency.

Intersymbol interference (ISI) is a significant source of degradation in many digital communication systems including our proposed non-far region communication system using large array antennas in the millimeter-wave band in which the main cause of ISI can be attributed to the path delay differences among the elements of an array antenna. This paper proposes a quantitative method to evaluate the ISI estimated from the measured near-field distribution of the array antenna. The influence of the uniformity in the aperture field distribution in ISI is discussed and compared with an ideally uniform excitation. The reliability of the proposed method is verified through a comparison with another method based on direct measurements of the transmission between the actual antennas. Finally, the signal to noise plus interference is evaluated based on the estimated ISI results and ISI is shown to be the dominant cause of the degradation in the reception zone of the system.

This paper presents moment method analysis of a plane wave generator in an oversized rectangular waveguide; its finite size is taken into account. Power divisions of the series of coupling windows and eigenmode excitation coefficients in the oversized waveguide are quantitatively evaluated by the analysis. In order to have a better understanding of array design, the relation between these mode coefficients and the radiation patterns is discussed. Control of the mode coefficients in the oversized waveguide is directly related to the far-field radiation pattern synthesis. These calculated results are verified by measurements in the 61.25 GHz band.

The authors propose a waveguide π-junction with an inductive wall. Galerkin's method of moments is applied to analyze it and small reflection and desired power division ratio is realized. Good agreement between the calculated result and the measured one verifies the design of a unit π-junction. The characteristics of aπ-junction with a wall are almost the same as those of a conventional π-junction with a post. Important advantage of the new π-junction with a wall is that it can be manufactured in the die-cast process of the waveguide while a post in the conventional one must be attached in an additional process. A 16-way power divider consisting of 8 π-junctions is designed at 11.85 GHz and the characteristics are predicted.

This paper presents the analysis and design of a reflection-cancelling transverse slot-pair array antenna with baffles by using the Spectrum of Two-Dimensional Solutions (S2DS) method. For the transverse slot array, the slot spacings with more than one free-space wavelength cause the grating-lobes. The baffles suppress the grating-lobes effectively. A one-dimensional slot array is extracted from the 2D array with in-phase excitation by assuming periodicity in the transversal direction. The uniform excitation over the finite array is synthesized iteratively to demonstrate the fast and accurate results by S2DS. A unit design model with the baffles is introduced to determine the initial parameters of the slot-pairs, which greatly accelerate the iterations process. Experiments at 25.3 GHz demonstrate the suppression of the grating lobes to the level less than -20.0 dB and also the good uniformity of the aperture field distribution.

Honeycomb structures are widely used in aerospace industry because of the lightweight and durable properties they provide. Here we propose to use a honeycomb core as the wave guiding structure in Radial Line Slot Antennas (RLSAs). This paper quantifies the propagation characteristics, especially the loss due to the honeycomb. At 32GHz, by choosing the proper cell size, both good isotropy and reasonably low effective dielectric constants are realized with the honeycomb as a spacer in a radial line waveguide. To estimate the material loss factor, several methods are compared and a factor of about 0.014∼0.018dB/mm is predicted and measured. A fabricated 90cm diameter honeycomb RLSA suffers about a 3.5∼5dB loss, which coincides with the estimates using the predicted loss factor.

This paper proposes a simple and practical scheme to decide the direction of a phased array antenna beam in wireless access systems using Radio-over-Fiber (RoF) technique. The feasibility of the proposed scheme is confirmed by the optical and wireless transmission experiments using 2GHz RoF signals. In addition, two-dimensional steering operation in the millimeter-wave band is demonstrated for targeting future high-speed wireless communication systems. The required system parameters for practical use are also provided by investigating the induced transmission penalties. The proposed detection scheme is applicable to two-dimensional antenna beam steering in the millimeter-wave band by properly designing the fiber length and wavelength variable range.

Dense millimeter-wave networks are a promising candidate for next-generation cellular systems enabling multiple gigabit-per-second data rates. A major disadvantage of millimeter-wave systems is signal disruption by rain, and here we propose a novel method for rain sensing using dual-frequency measurements at 25 and 38GHz from a small-scale Tokyo Institute of Technology (Tokyo Tech) millimeter-wave network. A real-time algorithm is developed for estimating the rain rate from attenuation using both ITU-R relationships and new coefficients that consider the effects of the rain Drop Size Distribution (DSD). The suggested procedure is tested on measured data, and its performance is evaluated. The results show that the proposed algorithm yields estimates that agree very well with rain gauge data.

This paper discusses how to design a Radial Line Slot Antenna (RLSA) whose waveguide is filled with high loss dielectric materials. We introduce a new design for the aperture slot coupling synthesis to restrain the dielectric losses and improve the antenna gain. Based on a newly defined slot coupling, a number of RLSAs with different sizes and loss factors are analyzed and their performances are predicted. Theoretical calculations suggest that the gain is sensitive to the material losses in the radial lines. The gain enhancement by using the new coupling formula is notable for larger antenna size and higher loss factor of the dielectric material. Three prototype RLSAs are designed and fabricated at 60GHz following different slot coupling syntheses, and their measured performances consolidate our theory.

A waveguide crossed-slot linear array with a matching element is accurately analyzed and designed by the method of moments using numerical-eigenmode basis functions developed by the authors. The rounded ends of crossed-slots are accurately modeled in the analysis. The initial values of the slot parameters determined by a model with assumption of periodicity of field are modified and refined by the full-wave finite-array analysis for uniform excitation and small axial ratio. As an example, an 8-element linear array is designed at 11.85 GHz, which radiates a circularly polarized wave at a beam-tilting angle of 50 degrees. The radiation pattern, the frequency characteristics of the reflection and the axial ratio are compared between the analysis and the measurement and they agree very well. The calculated and measured axial ratio at the beam direction are 0.1 dB and 1.7 dB, respectively. This method provides a basic and powerful design tool for slotted waveguide arrays.

We proposed a through-hole based transformer between microstrip line and post-wall waveguide (PWW). The transformer is based on a through-hole which is electrically separated from top and bottom broad walls of a waveguide by ring-shaped spaces. The proposed transformer shows a considerable merit compared with a conventional one based on blind-via in terms of fabrication and cost because it can be realized by through-holes in general printed-circuit-board technology. We selected liquid crystal polymer (LCP) as the material of substrates because of its lower dielectric loss and easy fabrication. The transformer was fabricated and measured. The loss associated with the mode conversion is estimated to be around 0.32,dB, and the bandwidth for a reflection smaller than $-15$,dB is 8,GHz, i.e., from 59 to 67,GHz.

A waveguide 2-plane hybrid coupler with two operating bands is proposed. The cross-sectional shape of the coupled region inside the proposed coupler is designed with a two-dimensional arbitrary geometry sorting method. Simulations of the proposed hybrid coupler has a fractional bandwidth (FBW) of 2.17% at the center of 24.99GHz, and at the center of 28.28GHz an FBW of 6.13%. The proposed coupler is analyzed by the mode-matching finite-element hybrid method, and the final result is obtained using a genetic algorithm. The analyzed result of the coupling for the main modes in the coupled region is presented. The design result is confirmed by measurements.

As a first step towards the realization of high-efficiency on-chip antennas for 60GHz-band wireless personal area networks, this paper proposes the fabrication of a patch antenna placed on a 200µm thick dielectric resin and fed through a hole in a silicon chip. Despite the large tan δ of the adopted material (0.015 at 50GHz), the thick resin reduces the conductor loss at the radiating element and a radiation efficiency of 78%, which includes the connecting loss from the bottom is predicted by simulation. This calculated value is verified in the millimeter-wave band by experiments in a reverberation chamber. Six stirrers are installed, one on each wall in the chamber, to create a statistical Rayleigh environment. The manufactured prototype antenna with a test jig demonstrates the radiation efficiency of 75% in the reverberation chamber. This agrees well with the simulated value of 76%, while the statistical measurement uncertainty of our handmade reverberation chamber is calculated as ±0.14dB.

A design of a linearly-polarized non-resonant waveguide broad-wall transverse slot linear array with suppressed grating lobes is presented. Each unit element in the array consists of a transverse slot, an inductive post and a parasitic dipole-pair at a height of half of the free space wavelength. It is designed as an isolated unit without considering mutual coupling by using the Method of Moments (MoM) for radiation suppression in grating beam direction and reflection cancellation at the input. The elements thus designed are used in a travelling wave array environment. It is predicted that the reflection is less than -20 dB at 11.95 GHz while the grating lobes are suppressed by more than 15 dB. The design and the characteristics of the array are confirmed by measurements.